Stainless steel plate is the general name of the stainless steel plate and acid resistant steel plate. It has been more than 90 years since it came out at the beginning of this century. Its surface is bright and clean, has high plasticity, toughness and mechanical strength, and is resistant to corrosion of acid, alkaline gas, solution and other media. It is a kind of alloy steel that is not easy to rust, but not absolutely rust free. Stainless steel plate refers to the corrosion resistant steel plate in a weak medium such as atmosphere, steam and water, while acid resistant steel plate refers to the corrosion resistant steel plate in a chemical corrosive medium such as acid, alkali and salt. All stainless steel plates have high temperature oxidation resistance, but the oxidation rate is affected by inherent factors such as exposure environment and product morphology.
Here is the content:
Stainless steel plate pasted on the wall
matters needing attention
Partial application of stainless steel plate
Stainless steel plate pasted on the wall
There are many ways to install the stainless steel plate on the wall according to the process requirements, installation purpose and construction cost requirements. The most commonly used methods are to fix the stainless steel plate directly with expansion bolts and drill holes on the wall with an impact drill, to paste the stainless steel plate with special glue, to fix the stainless steel plate with special glue, to deal with the foundation, to install the frame, and then to install the stainless steel plate. This method should be more appropriate. Do a good job of wall treatment before installation. Before the installation, the wall and the interior of the wall in the installation area should be well treated. The water and electricity pipelines in the wall should be installed according to the scheme, and the relevant pressure pipes have been tested and meet the requirements. The wall has been leveled, and the wall should be dry, with the corresponding construction conditions. Get ready for marking. According to the specific construction scheme and requirements, according to the height and width of the floor, the elevation of the wall is treated, the height is measured with a box ruler, and the wall is graded and marked. This is the "snapping line" construction step in the construction. The specific marking should be very careful, and the marking is clear. This step determines whether the stainless steel plate installation is smooth, whether the gap between the plates is appropriate, and has a great influence on the whole construction The quality of construction has an important impact. Install the keel. After marking, the installation of keel will begin. Here is a simple popularization of what is the keel, keel is used to support the wall shape, fixed structure of a building material, is a very common skeleton used in decoration. The keel installation shall be carried out in general order, from suspender, large keel, small keel, layering, etc. during the construction, attention shall be paid to the accurate installation according to the marking line, the connection shall be firmly fixed with bolts and screws, and the spacing between each other shall be set aside according to the routine, so as to facilitate the installation of stainless steel plate. Do antirust treatment well.
The keel should be made of metal material, which is generally placed on the wall, and the panel should be buckled on it. It will be oxidized and rusted for a long time, which will affect the safety of the material. Therefore, after installation, rust removal should be carried out. The key point is to brush antirust paint on the surface of welding joint, such as connecting point, fixed point, etc. before the next process, and do the relevant treatment well. Install the stainless steel plate. Before installing the stainless steel plate, it is necessary to check and accept the early construction to ensure that the construction technology is qualified, because after installing the stainless steel plate, the early construction is covered, so it is not convenient to check and accept again. After the acceptance, the installation of stainless steel plate shall be started. If it is a whole steel plate, it shall be installed directly and sealed and pressed with a strip. If it is multiple steel plates, it is necessary to install one plate, seal one plate with a strip, and ensure the straight installation along the keel marking line.
matters needing attention
In the process of installation, it is necessary to pay attention to the construction in strict accordance with the operation specifications. When installing, it should be handled with care to avoid deformation and damage of relevant parts, do not contact with other hard objects, avoid scratch damage of stainless steel surface, and affect the effect. The stainless steel plate and keel should be firmly buckled, and the corresponding moisture-proof, heat insulation, rust prevention and other treatment should be done.
Partial application of stainless steel plate
The use of 304 stainless steel plate makes it suitable for the roof covering materials. Because this material is easy to form, durable and beautiful, many architects choose stainless steel as the protective layer. 304 as the most widely used stainless steel, heat-resistant steel, food equipment, general equipment, atomic energy industrial equipment. It has good corrosion resistance, heat resistance, low temperature strength and mechanical properties. 304 stainless steel contains chromium, which has high chemical stability. It can form a passive film on the surface of the steel, isolate the metal from the outside world, protect the steel plate from oxidation, and improve the corrosion resistance of the steel plate. Stainless steel plate has a smooth surface, high plasticity, toughness and mechanical strength, and is resistant to corrosion of acid, alkaline gas, solution and other media.
If you want to better use stainless steel products in more aspects, then Jiangsu C.J.M Stainless Steel Group must come to have a look. We have a very comprehensive stainless steel plate product, can meet your stainless steel plate in any place, any demand. Tel. + 86-18092577236, post office postmaster@ssplatechina.com.
